Australia’s got a tough limit on HFC imports for 2026 and 2027, just 4.25 million tonnes of CO2 equivalent. Compare that to the 6.43 million tonnes they’d normally be allowed under the Montreal Protocol. Less gas coming in means every single kilogram that slips away counts. And those little joints are one of the places where losses can add up, like a flare that forms at the end of a tube with a special tool.
A Seal That’s Just Metal to Metal
Making a flare is dead easy with a flaring tool, no solder or brazing rod required. You just stretch the end of a tube out into a cone shape, press it against another cone in a matching fitting and that’s it, all metal, all sealed. As long as those cones are nice and even, of course.
These things are pretty handy for service work where access is tight; you can just open ’em up and remake the seal. And don’t worry, the seal won’t give way just because it’s been opened and closed a few times. 45-degree flares are common in aircon work, but the type of seal you need will depend on what the job requires, and the manufacturer’s instructions will always tell you what’s right.
Getting the Tube Ready for a Good Flare
Most of the problems with flares start before you even pick up the tool. If the cut on the pipe isn’t square, or there’s any debris or burrs inside the pipe, you’re in trouble from the get-go. And don’t forget to put the flare nut on the end of the pipe first; it can be a real ‘aha’ moment when you remember that after you’ve already formed the cone.
How much pipe sticks out above the bar determines the size of the cone you’ll end up with. Too little and it won’t seal properly; too much and it’ll get in the way of the nut. Just follow the instructions from the tool manufacturer and you’ll be right.

How the Tube Affects the Result?
The type of tube you’re using can make all the difference when it comes to flaring. Different materials behave differently under heat; some are soft and squishy while others are hard as nails. And if you turn the feed screw too fast, some of those materials will crack under the pressure. So just remember to follow the manufacturer’s advice and use the right tool for the job.
No need to get out the testing gear for this one; just follow the instructions and you’ll be fine. The tube supplier and the tool manual will always give you the lowdown on what works and what doesn’t.
Licence Required
If you’re working on refrigeration and aircon equipment, you need a Refrigerant Handling Licence. Don’t even think about touching the stuff without one; it’s against the law. And the Australian Refrigeration Council is the one that keeps track of who’s got what licence.
It’s not just the handling of the refrigerant that’s covered by the rules though; what happens to it afterwards is pretty important too. The gas needs to get back into the supply chain, not just get released into thin air. Which is why recovery equipment goes hand in hand with a flaring kit on any job that’s done right.
Testing Of The Joint Prior To Departure From The Site
A perfectly good-looking flare may be leaking. Pressure testing with nitrogen, holding a vacuum and checking leaks electronically are all routine tests in the trade, with each method picking up on different faults. An overnight drop in pressure could indicate a fault that would not show up under visual inspection.
Remaking a flare is a matter of minutes; returning to a job can take an entire morning. The HFC phase-down provides yet another reason for caution. The process started in January 2018 and will end up with an 85% reduction by 31 December 2035. Older equipment is unaffected, with HFCs remaining available for servicing of it. Flaring joints in existing equipment will thus need fixing for years to come.
Questions To Ask Before Remaking The Next Flare
Is the flare type compatible with the fitting? Was the tube cut square, deburred and the projection made in accordance with the manufacturer’s instructions? Have you done a leak test, and do you have a valid licence?
Taking care of all four items above reduces the likelihood that the little cone in your line will become a weak spot. Failure to ask any one of the questions may come back to you years later, as some other technician is working out on the rooftop the reason for your gauge not holding.